Product Title Stock No. Product No.
Pushbutton‚ triple‚ with status LED‚ with scene controller‚ with IR receiver decoder‚ titanium
white
5WG1223-2DB15 UP 223/15
Pushbutton‚ triple‚ with status LED‚ with scene controller‚ with IR receiver decoder‚ aluminum
metallic
5WG1223-2DB35 UP 223/35

The bus transceiver module (BTM) (see Chapter System Products and Accessories) or flush-mounting actuator with bus transceiver module
(BTM) must be ordered separately. The matching design frame must be ordered separately. See Chapter Display and Operation Units – Pushbutton
accessories.
IR remote controls and IR wall-mounted transmitters must be ordered separately. See chapter Display and Operation Units – Remote controls.

Multifunctional display-/control panel for KNX with Dot-Matrix LCD display 96 x 128 pixels
V For the display and control of at least 10 adjustable room control functions:
– Switching toggle/On/Off
– Door bell function On/Off
– Dimming
– Solar protection control
– Send 1 Byte/2 Byte value
– Display 1 Bit/1 Byte/2 Byte value
– Forced control
– Display text messages
– Recall and save scenes
– Warning and alarm messaging
V 8 capacitive touch buttons for horizontal operation‚ blocking selectable for each function and configurable
for each function depending on the value of the blocking object
V Green/red LED als Orientierungslicht‚ as orientation light‚ as status indication‚ as a response to pressing
a button respectively to the signalling of alarm reports
V A signaler for acoustical alarm reports respectively as a status of the touch operation
V Integrated room temperature sensor
V Evaluation and weighting of an external inside temperature sensor
V Room temperature control configurable as two-step control and/or continuous control‚ for exclusive
heating operation‚ exclusive cooling operation or heating and cooling operation
V Selectable operating modes over the KNX:
– Comfort
– Pre-comfort
– Energy-savings and protection
V Local indication
– Of the active operating modes or automatic- respectively manual mode
– Inside temperature or outside temperature
– Heating or cooling mode
– Dew point alarm
– Open windows
V Local switching between
– Manual- and automatic mode
– Comfort‚ pre-comfort‚ energy-saving- and protection mode
V Adjustable time-limited extension of the comfort mode
V Adjustable room temperature setpoint shifting for comfort mode
V Via KNX set basic setpoint value of the room temperature for comfort mode
V An outside temperature based temperature setpoint value tracing in the cooling operation
V Adjustable dead zone between the heating setpoint value and the cooling setpoint value for comfort
mode
V Transmission of controller output(s) either as On/Off switching commands or as control commands in
the range 0…100 %
V Local display of the manually selected fan rotational speed respectively of the automatic adjustment
of the fan rotational speed
V Adjustable fan rotational speed respectively automatic adjustment of the fan rotational speed on the
controller
V Weekly schedule programme for controller- operating modes‚ automatic mode and at the least 8 room
control functions
V At the least 40 schedule tasks and Display and set of the date and time
V User control of LCD background lighting and Background color
V Display system settings and room temperature controller in the languages: German‚ English‚ French‚
Italian od Spanish
V User setting of at least 3 operating languages also Integrated bus coupling unit‚ bus connection via
bus terminal possible
V Flush mounted device for the mounting in an flush wall box Ø 60 mm‚ for fixing on the mounting plate
AQR2500NF via lateral springs (separately specified)

Multifunctional display/operating device for KNX‚ with 320 x 240 pixel‚ 2.8″ LCD color display
V For the display and operation of at least 18 configurable room operator functions:
– Switching On/Off/Over and Pushbutton function (bell function)
– Shutter/blind/roller control
– Value transmission: 1 byte in %‚ 1 byte integer without prefix‚ 1 byte integer with prefix‚ 2 byte integer
without prefix‚ 2 byte integer with prefix
– Positively driven operation
– Scene control: Store and call up scene 8 bit‚ store and call up scene 1 bit
– Text display and warning and alarm indications
V Operation using touch screen and/or by turning/pushing rotary/push button
V RGB LED as orientation light or for signaling alarm indications
V Buzzer for acoustic alarm indication or as feedback when operating touch screen
V Integrated room temperature sensors
V Analysis and weighting of an external inside temperature sensor
V Room temperature control can be set as a two-point control and/or continuous-action control for
heating only‚ for cooling only‚ or for heating and cooling mode
V Operating modes that can be switched via KNX: comfort mode‚ pre-comfort mode‚ energy-saving
mode and frost or heat protection mode
V Local displaying of active operating modes or automatic or manual modes
V Local displaying of heating/cooling valve open‚ dew point alarm and open window
V Local switchover between automatic or manual mode‚ and between comfort‚ pre-comfort‚ energy-saving
and protection modes
V Local‚ time-adjustable extension of comfort mode
V The room temperature setpoint value for comfort mode can be set via a rotary button on the room
controller
V Basic room temperature setpoint value for comfort mode which can be set via the KNX
V Outdoor temperature-based tracking of temperature setpoint value in cooling mode
V Adjustable dead zone between the heating setpoint and the cooling setpoint for comfort mode
V Two-level heating or cooling
V Output of the control variable(s) either as an on/off switch command or as a positioning command in
the range of 0…100%
V Local displaying of manually set fan speed step or automatic speed input
V Fan speed step can be set via the rotary button or entered automatically by the controller
V Weekly scheduling program for controller operating modes and for 18 room operator functions
V At least 16 time switching points per function per weekday
V Display of date and time
V Selection of at least 4 different design templates as operator and display interface
V Local activation of a cleaning function to lock the touch screen and the rotary/push button
V Slot for a micro SD card for transferring firmware and configuration data
V incl. bus coupling unit (included in delivery)
V Bus connection via bus terminal
V Connection of the separate 24 V DC boost voltage‚ power consumption approx. 50 mA
V Flush-mounting device for mounting in a Ø 60 mm installation box‚ with screw fixing

Product Title Stock No. Product No.
Room Controller Contouch‚ incl. bus coupling unit‚ titanium white 5WG1204-2AB11 UP 204/11
Room Controller Contouch‚ incl. bus coupling unit‚ carbon metallic 5WG1204-2AB21 UP 204/21
Room Controller Contouch‚ incl. bus coupling unit‚ aluminium metallic 5WG1204-2AB31 UP 204/31
Room Controller Contouch‚ incl. bus coupling unit‚ piano black 5WG1204-2AB51 UP 204/51